You may order the foot-switch from Peavey (part # 90001791). Nashville 112 80-Watt 1x12 Pedal Steel Guitar Amp. This particular amp has had the speaker changed to the Telonics TSNEO 12-4 (12 - 4 ohm). Just unplug the internal speaker and use the extension output (already wired) to go in any 4ohm 15 works great! I use the Telonics 15-4 cabinet.I've also installed knob guards to protect the front of the amp. Fender Tilt Back Legs have been installed. Peavey's Nashville Series has long been the standard for steel guitarists, and the company's support of this genre continues with the introduction of the Nashville 112. This amp has the Telonics 12.
Pre-EQ patch send return for volume pedal patch. Modified active low, mid, mid/shift, high and presence EQ.
Preamp out/CD in and power amp in patch. Headphone input jack that defeats internal speaker for quiet rehearsal. 80 watts, 12 inch Blue Marvel® speaker (specially voiced for steel).Weight Unpacked: 42.80 lb(19.414 kg). Weight Packed: 50.00 lb(22.68 kg). Width Packed: 19.488(49.49952 cm).
Height Packed: 23.228(58.99912 cm). Depth Packed: 12.205(31.0007 cm). Intended to alert the user to the presence of uninsulated dangerous voltage within the products. Enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Intended to alert the user of the presence of important operating and maintenance (servicing). Instructions in the literature accompanying the product. CAUTION: Risk of electrical shock DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover.
No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture.
Before using this appliance, read the operating guide for further warnings. Este símbolo tiene el propósito, de alertar al usuario de la presencia de (voltaje) peligroso sin. Aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para. Constituir riesgo de descarga eléctrica. Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones importantes sobre la.
Operación y mantenimiento en la información que viene con el producto. PRECAUCION: Riesgo de descarga eléctrica ¡NO ABRIR! PRECAUCION: Para disminuír el riesgo de descarga eléctrica, no abra la cubierta. Deje todo mantenimiento en manos del personal técnico cualificado. ADVERTENCIA: Para evitar descargas eléctricas o peligro de incendio, no deje expuesto a la lluvia o.Humedad este aparato Antes de usar este aparato, Iea más advertencias en la guía de operación. Ce symbole est utilisé dans ce manuel pour indiquer à lutilisateur la présence dune tension dangereuse. Pouvant être damplitude suffisante pour constituer un risque de choc électrique.
Ce symbole est utilisé dans ce manuel pour indiquer à lutilisateur quil ou quelle trouvera dimportantes. Instructions concernant lutilisation et lentretien de lappareil dans le paragraphe signalé. ATTENTION: Risques de choc électrique NE PAS OUVRIR! ATTENTION: Afin de réduire le risque de choc électrique, ne pas enlever le couvercle.Il ne se trouve à. Lintérieur aucune pièce pouvant être reparée par lutilisateur.
Confiez Ientretien et la réparation de. Lappareil à un réparateur Peavey agréé. AVERTISSEMENT: Afin de prévenir les risques de décharge électrique ou de feu, nexposez pas cet. Appareil à la pluie ou à lhumidité.
Avant dutiliser cet appareil, lisez attentivement les avertissements. Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen innerhalb des Gehäuses. Warnen, die von Ausreichender Stärke sind, um einen elektrischen Schlag verursachen zu können. Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam.
Machen, die Handhabung und Wartung des Produkts betreffen. VORSICHT: Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Befinden sich keine Teile darin, die vom Anwender repariert werden könnten. ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gerät nicht dem.
Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen. WARNING: When using electrical products, basic cautions should always be followed, including the following.Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings.
Install in accordance with manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers). Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one.
A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is. If the provided plug does not fit into your outlet, consult an electrician for replacement of the.Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point. They exit from the apparatus. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your.
A The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E the earth. Symbol colored green or colored green and yellow. B The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. C The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red. Cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any. Way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus. The apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.Never break off the ground pin. Write for our free booklet Shock Hazard and Grounding. Connect only to a power. Supply of the type marked on the unit adjacent to the power supply cord.
If this product is to be mounted in an equipment rack, rear support should be provided. Exposure to extremely high noise levels may cause a permanent hearing loss.
Individuals vary considerably in susceptibility. To noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise. Governments Occupational Safety and Health Administration (OSHA) has specified the.
Following permissible noise level exposures. Duration Per Day In Hours Sound Level dBA, Slow Response. According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the.Ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure. Is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is. Recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be. Protected by hearing protectors while this unit is in operation. As the leader in steel guitar amplification. We are proud to offer you this smaller, more portable, lightweight cousin to the popular Nashville 1000.
This amp has all of the same front panel features as the 1000 along with a newly designed 80. Watt power section, an added headphone jack, and a CD input which makes it an ideal choice for practice. The Nashville 112 also features a long-pan Accutronics reverb and a newly designed 12. Blue Marvel speaker that has been carefully voiced for steel guitar applications.We know you are anxious to start playing, so weve included a Quick Start section and a. These are certain to get you on your way. However, it is important that. You read the safety precautions first. Scan through this manual and locate.
Each safety icon is followed by a warning. Read that warning carefully before continuing.Read all of the warnings , refer to the Quick Start section below if you so desire. You read this manual in its entirety to fully understand the functions of each. Quick Start - I just wanna play!
The following section takes a jump in and get your feet wet approach. If any part seems confusing, refer to the. More detailed sections that follow. Insure that you have read and understand all safety warnings noted through-out the manual. Imperative that you follow these precautions for the safety of yourself and your amp.
With the amp turned off, plug the power cord into the proper voltage supply indicated on the back of the. Unit near the cord retainer. Plug your guitar into either the High or Low Gain input and turn all knobs counterclockwise to their 0.
Using the Recommended Settings on page 8, find the type of tone that most closely resembles the tone. Set the knobs on the front of the unit to match the setting you have selected. Turn your guitar volume down and turn the amp on via the power switch on the back of the unit. Step 7 Gradually turn the volume of your guitar all the way up or until you are comfortable with the level/tone. Step 8 To adjust the overall level, use the Master Gain control.To adjust out any undesirable distortion, use the Pre Gain knob. Turning the knob counter-clockwise results. In a decreased level, thus reducing the overdriven signal. Any external effects units can also cause the signal to. You should be able to play at this time. Vary the Reverb and/or EQ knobs to get a feel for their effect on. READ THE REST OF THIS MANUAL.
High Gain Input used for most electric guitars. It is 10 dB louder than the Low Gain input.
Low Gain is provided for instruments that have extremely high outputs, which can result in overdriving (distorting). If both inputs are used simultaneously, the output levels are the same Both are low gain. Pre Gain controls the input level of the Nashville 112. Adjusting this control clockwise will increase the input level. Resulting in a hotter, more responsive signal.(4) Pre EQ Patch (Volume Pedal Patch). These 1/4 mono jacks allow for Pre EQ effects patching. Connect a quality shielded instrument cable between. The send jack and the input of your external effects unit. Connect another quality shielded instrument cable. From the output of your effects unit to the return jack. Pay attention to the external effects unit levels input and. Consult the owners manual for your effects unit. It should be noted that too strong a. Signal at the return jack can overdrive the EQ section of the Nashville 112.
If this happens, the effects unit output. (5) Low, Mid, and High EQ. This section is an active tone control.Adjusting these knobs clockwise from the center (0) position will amplify. The low, mid, or high frequency content. Adjusting counterclockwise from the center (0) position will attenuate the. Low, mid, or high frequency content. The Shift knob changes the center frequency of the Mid EQ (5), allowing you to tailor the Nashville 112 EQ to. The center frequency can be adjusted from 150 Hz to 1.5 kHz. That the further you turn the knob away from a frequency, the less affect the Mid EQ will have on that frequency. Note: The shift and MID controls interact in determining the preferred mid-range settings. Presence is an active tone control that boosts the extreme high frequencies up to 15 dB. Similar to the Pre EQ Patch(4), these jacks are post EQ. The return level should still. Be monitored for its strength.
In addition, the Post EQ Patch can be taken in and out of the signal path via the. Adjusting this control clockwise will result in more reverb content in the output of the amp. Defeated by rotating the control counterclockwise or via the footswitch (not included). 1 2 3 4 5 6 5 7 8 9 10 11. The Master Gain controls the overall volume level of the amplifier.The final adjustment to this control should be. Made after the desired sound/tone has been achieved. The Power LED illuminates when power is supplied to the amp. If this LED is lit, the amp is on. Placing this switch in the On position will result in power being supplied to the unit. The Power LED (11) will. Illuminate when the amp is on.
This mono 1/4 jack provides an input to the power amplifier. When used in conjunction with the Preamp Out jack.(14), an effects loop is formed allowing the use of external equalizers and effects. (14) Preamp Out / CD Input. This mono 1/4 jack provides an output from the preamp. When used in conjunction with the Power Amp In jack. (13), an effects loop is formed allowing the use of external equalizers and effects. This jack can also be used to. Connect the output of a CD or tape player to the power amp for play along practicing. Should be used to connect to the CD input. The Line Out XLR jack offers you a balanced, low impedance output to go to a mixing board or snake. Help to eliminate mics on stage as well as loud levels. This results in less chance of feedback as well. Mic cables to make this patch. A headphone jack is provided for stereo headphones. This switching jack disengages the internal speaker when. This jack is provided for the connection of the optional footswitch (part #90001791). The footswitch is a multifunction. Type, allowing you to to defeat the Reverb and/or the Post EQ Patch loop. To use the footswitch, insure. That the footswitch plug is inserted fully into the jack. This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to. This connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line.
Voltage is used (see voltage marking on unit). Never remove or cut the ground pin of the line cord plug.
Is supplied with a properly rated line cord. When lost or damaged, replace this cord with one of the proper ratings. 12 13 14 15 16 17. Low Mid Shift High Pres. For CLEAN settings: the MASTER should be a higher setting than the PRE GAIN to avoid premature signal clipping.
80 Watts RMS into 4 Ohms with DDT. Less than 0.3%, 1 Watt to 80 Watts RMS. 20 Hz to 20 kHz, 4 Ohms. Below 0.8% THD for 6 dB overload. Below 3.5% THD for 20 dB overload.
Greater than 83 dB below rated power. 200 Watts, 50/60 Hz, 120 VAC (domestic). With the controls preset as follows. Preamp high gain input (no pad). Impedance: High Z, 220 k Ohms.Nominal input level: -29.9 dBV, 32 mV RMS. Minimum input level: -53.2 dBV, 2.2 mV RMS. Maximum input level: 8 dBV, 2.5 V RMS. Preamp Low Gain Input (-10 dB pad). Impedance: High Z, 68k Ohms. Nominal input level: -19.9 dBV, 101 mV RMS. Minimum input level: -43.2 dBV, 6.9 mV RMS. Maximum input level: 18 dBV, 8 V RMS.
Load impedance: 10k Ohms or greater. Nominal output level: -18.6 dBV, 117 mV RMS.
Designed Input Level: -18.6 dBV, 117 mV RMS. Switching jack provides send to return.
Load impedance: 10 k Ohms or greater. Nominal output level: -14.1 dBV, 198 mV RMS. Impedance: High Z, 1 m Ohms.Designed Input Level: -14.1 dBV, 198 mV RMS. Load impedance: 5 k Ohms or greater. Nominal output level: -3.1 dBV, 0.7 V RMS.
Preamp output / CD input. Nominal CD Input Level: -3.1 dBV, 0.7 V RMS.
Stereo cable must be used for CD Input. Impedance: High Z, 27 k Ohms. Designed Input Level: -3.1 dBV, 0.7 V RMS. Switching jack provides preamp output. To power amp input connection when not.
(20 Hz to 20 kHz unweighted). Greater than 75 dB below rated power. Mid Shift: 150 Hz to 1.5 kHz. Select effects: Post EQ effects Loop defeat.Dimensions (H x W x D). 18.125" x 21.375" x 10.250. Effective Date: July 1, 1998.
Guitars/Basses, Amplifiers, Pre-Amplifiers, Mixers, Electronic. Crossovers and Equalizers 2 years (+ 3 years). Drums 2 years (+ 1 year).Enclosures 3 years (+ 2 years). Digital Effect Devices and Keyboard and MIDI Controllers 1 year (+ 1 year). Diaphragm replacement kits and passive crossovers. And all Accessories 1 year.
Tubes and Meters 90 days. 95 Shields Court, Markham, Ontario, Canada L3R 9T5. Include a detailed description of the problem, together with a copy of your sales receipt or. Also provide a complete return address. ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE.PEAVEY'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT PEAVEY'S OPTION. REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PEAVEY SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS OF. USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL. CONSEQUENTIAL OR OTHERWISE, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Features and specifications subject to change without notice. Peavey Electronics Corporation 711 A Street Meridian, MS 39301. The item "Nashville 112 80-Watt 1x12 Pedal Steel Guitar Amp Customized VERY NICE" is in sale since Wednesday, November 4, 2020. This item is in the category "Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers". The seller is "stylesupportmidi" and is located in Redmond, Washington. This item can be shipped to United States.